Ans:Note: Here, in Afin calculation the pin surface area is multiplied by 9 because there are 9 fins. It depends on number of fins attached.

Thermodynamics ForumJul 20, 2022Thermal Efficiency of Rankine Cycle - GATE ME '98LikeReactions00 comments0Views

Thermodynamics ForumJun 18, 2021What is work producing device and what is work consuming device according to thermodynamics?LikeReactions10 comments0Views

Thermodynamics ForumJul 01, 2022What is the difference between Nusselt number and Biot number?LikeReactions00 comments0Views

Thermodynamics ForumJul 20, 2022Air-Fuel ratio in Gas Turbine - GATE ME '98LikeReactions00 comments0Views

Thermodynamics ForumMay 05, 2022What is an exact differential and what is an inexact differential?LikeReactions00 comments0Views

Thermodynamics ForumJul 14, 2022What is the difference between LMTD and AMTD?LikeReactions00 comments0Views

justincorhadApr 05, 2022Does this water pumping device use the Rankine cycle?LikeReactions015 comments15Views

Thermodynamics ForumJul 14, 2022What are the limitations of the LMTD method?LikeReactions00 comments0Views

Thermodynamics ForumMay 05, 2022Why do the heat and work are path functions?LikeReactions00 comments0Views

Thermodynamics ForumJul 11, 2022What is Dittus-Boelter equation? What are the assumptions and limitations of the Dittus-Boelter equation?LikeReactions00 comments0Views

Thermodynamics ForumMay 12, 2022How to calculate pump work in the Rankine cycle?LikeReactions00 comments0Views

Thermodynamics ForumMay 31, 2022What is the criteria for lumped system analysis?LikeReactions00 comments0Views

Thermodynamics ForumJul 22, 2022Equation of streamline from velocity components - GATE ME '06LikeReactions00 comments0Views

Thermodynamics ForumDec 08, 2022What is the relation between average velocity and maximum velocity in fully developed laminar pipe flow? LikeReactions00 comments0Views

Thermodynamics ForumJul 20, 2022Regenerative Gas Turbine Cycle - GATE '97 ME LikeReactions00 comments0Views

Thermodynamics Forum2 minThermodynamics Misconceptions ExposedAs engineers, our world revolves around the fundamental laws that govern energy and its transformations. Thermodynamics, the backbone of...

Thermodynamics Forum2 minUnlocking the Secrets of Thermodynamics: A Beginner's GuideWelcome, aspiring scientists and engineers! Today, we're delving into the fascinating world of thermodynamics, where heat, energy, and...

Thermodynamics Forum2 minBest online resources to study Thermodynamics, Fluid Mechanics, and Heat TransferI have been researching about best reference books, best lecture series, and best universities to study thermal sciences since I was in...

Thermodynamics Forum1 minApproximate Values of Heat Transfer CoefficientThe higher the value of heat transfer the faster will be the heat transfer according to Newton's law of cooling.

Thermodynamics Forum1 minVolumetric Flow Rate - 5W1HIt is a measure of the quantity of the fluid that is being displaced from one place to other. This is an important parameter when designing

Thermodynamics Forum4 minThrottling ProcessThe pressure drop in the thermal system can be obtained by expanding the fluid in the expansion valve which produces thermodynamic work.

Thermodynamics Forum3 minPath Function vs Point FunctionWe come across a lot of properties and functions in Thermodynamics. These are divided mainly into path functions and point functions. All...

Thermodynamics Forum2 minThe Carnot PrinciplesThe efficiency of an irreversible heat engine is always less than the efficiency of a reversible engine operating between the same two

Thermodynamics Forum3 minTemperature-Entropy(T-s) DiagramThe T-s diagram is one of the most used plots in Thermodynamics. It is used to analyze vapor power cycles, gas power cycles, and

Thermodynamics Forum1 minPetrol in Diesel Engine and Diesel in Petrol Engine One can not fill diesel in petrol engine because nozzle that is used for diesel is bigger than filler neck of the petrol tank.